Garage floors

Garage Floor Epoxy in Toronto & the GTA

A flake epoxy garage floor gives you a seamless, easy-to-clean surface that shrugs off road salt, oil and hot tires. Every slab is diamond ground before a drop of resin goes down.

  • Free on-site measure and a firm written price
  • Diamond grinding, crack repair and dust extraction on every job
  • Flake, solid or metallic finish in the colour you choose
647-621-5060

Mon–Sat, 7am–7pm · Toronto & the GTA

Limited time

Claim your $500 off

Only 3 install slots left this month

Step 1/3

What are we coating?

The system

What a flake epoxy garage floor actually is.

A flake floor is built in layers on the slab you already have. First a high-build epoxy base coat, then vinyl flake broadcast across the whole floor until the resin refuses any more, then a polyaspartic top coat that locks the flake in.

The flake is what gives the floor its speckled finish, which hides dust, tyre marks and the small imperfections every garage slab has. The top coat is what you actually walk and drive on.

Because it cures as one continuous sheet, there are no joints or grout lines to sweep out. It is bonded to the concrete rather than sitting on top of it, so it does not lift at the edges or trap water underneath.

Prep

Why we diamond grind every slab first.

Epoxy does not stick to concrete. It sticks to the profile of the concrete. Acid washing or a paint-on etcher leaves the laitance and the slick trowel finish in place, so the coating bonds to a dusty skin instead of the slab.

In a garage that failure shows up fast. Road salt and freeze-thaw work their way under the edge of a coating, water gets in, and the floor peels or flakes off within a couple of years.

Diamond grinding takes off that top layer, opens the pores and leaves a mechanical key the epoxy can lock into. We grind every slab we coat, new concrete included, and we cut out and fill cracks and spalls before the first coat goes down.

  1. 01

    Grind

    Diamond grinders with dust extraction take the slab back to clean, open concrete.

  2. 02

    Repair

    Cracks, spalls and failing patches are cut out and filled with epoxy mortar.

  3. 03

    Coat

    Epoxy base coat, flake broadcast to refusal, then a polyaspartic top coat.

What you get

Built for the way a garage actually gets used.

Salt in February, oil in July, hot tires all summer. The floor has to take all of it without staining or going slick.

Resists salt, oil and stains

Road salt, brake dust, antifreeze and spilled oil sit on the surface instead of soaking into the slab.

Seamless

One continuous floor with no joints or grout lines for grit, water and dirt to collect in.

Easy to clean

Sweep it or hose it down. There is no texture to scrub and nothing to shampoo.

Slip resistant

The flake gives the floor its texture, and we add a slip-resistant aggregate to the top coat.

Sizes

One, two and three car garages.

The system is the same at every size. What changes is the square footage, the slab condition and the finish you pick.

1 car

About 200 – 300 sq ft

The fastest install of the three. A full flake system in the colour you pick, usually done in a single visit after prep.

2 car

About 400 – 500 sq ft

The garage we coat most often. Big enough for a metallic or full-broadcast flake finish without the price jumping.

3 car

600 – 800 sq ft and up

Same system on a bigger slab. We plan the pour in sections so the coating stays wet-in-wet and the finish is even.

Installed pricing starts at [PRICE] per sq ft. Your firm number comes after the free measure, because size, slab condition and finish all move it.

Before & after

Same slab, same angle.

Photos from recent garage installs around the GTA. Only the floor changes.

Before
After
Two-car garage · Etobicoke
Before
After
Single garage · Mississauga

$500 off your project · limited time

Get your floor priced before the season fills up.

Answer three questions and we'll come out, measure and put a fixed number in writing. Free, no obligation.

Only 3 install slots left this month